Ospray

Product	Active Constituent(s):	Registered For:	Overview	Documents
APVMA Code :62160	225g/L methomyl(an anticholinesterase compound)	Commercial Use  Domestic Use	For the control of certain insect pests. Chemical Group carbamates	MSDS Label

General Instructions

Addition of Wetting Agent

When diluting with water, add a non-ionic surfactant at registered label rates.

Spray Preparation

Quarter to half fill spray tank with water. Start agitation (DO NOT use air agitation). Add the required amount of this product to the tank and complete filling with water. Add a non-ionic surfactant as recommended above. Continue agitation for several minutes prior to spraying to fully mix the chemical.

Application

a) Larvicidal:

Apply at the recommended rates when the infestation reaches an economically damaging level and repeat as needed. Apply the lower rates on small larvae and on light infestations of insects. Use the higher rate on large larvae and heavier infestations of insects. Best control is obtained when young insects are treated.

b) Ovicidal/Larvicidal:

Use these rates only where crops are regularly monitored for eggs and larvae. Use the lower rate when only eggs are present. Use the higher rate when heavy egg lays occur and/or when larvae are less than 3 mm long. If larvae are longer than 3 mm use the larvicidal rates. This product may be used at ovicidal/larvicidal rates in conjunction with other recommended larvicides used to control other insects.

Tree and Vine Crops - Dilute Spraying:

- Use a sprayer designed to apply high volumes of water up to the point of runoff and matched to the crop being sprayed.

- Set up and operate the sprayer to achieve even coverage throughout the crop canopy. Apply sufficient water to cover the crop to the point of run-off. Avoid excessive run-off.

- The required water volume may be determined by applying different test volumes using different settings on the sprayer, from industry guidelines or expert advice.

- Add the amount of product specified in the Directions for Use Table for each 100 L of water. Spray to the point of run-off.

- The required dilute spray volume will change and the sprayer set up and operation may also need to be changed as the crop grows.

Tree and Vine Crops - Concentrate Spraying:

- Use a sprayer designed and set up for concentrate spraying (that is: a sprayer which applies water volumes less than those required to reach the point of run-off) and matched to the crop being sprayed.

- Set up and operate the sprayer to achieve even coverage throughout the crop canopy using your chosen water volume.

- Determine an appropriate dilute spray volume (See Dilute Spraying above) for the crop canopy. This is needed to calculate the concentrate mixing rate.

- The mixing rate for concentrate spraying can then be calculated in the following way:

EXAMPLE ONLY:

1. Dilute spray volume as determined above. For example: 1500 L/ha

2. Your chosen concentrate spray volume: For example: 500 L/ha

3. The concentration factor in this example is: 3 X (ie: 1500 L / 500 L = 3)

4. If the dilute label rate is 100 g/100 L, then the concentrate rate becomes 3 x 100, that is, 300 g/100 L of concentrate spray.

- The chosen spray volume, amount of product per 100 L of water, and the sprayer set up and operation may need to be changed as the crop grows.

- For further information on concentrate spraying, users are advised to consult relevant industry guidelines, undertake appropriate competency training and follow industry Best Practices.

For concentrate application, use a spray volume of at least 200 litres per hectare.

For dilute application, apply to run-off. See Dilute Spraying above.

Non-tree and vine crops - Ground Application:

Apply as a fine spray preferably generated by cone nozzles. DO NOT apply as a fog or mist. For effective insect control, proper timing and good coverage are essential. Use sufficient water to obtain thorough uniform coverage. Use 100-400 L/ha spray mixture unless otherwise directed in the Directions for Use section.

Aerial Application

For ADZUKI BEANS, CANOLA, COTTON, LINSEED, LUCERNE, LUPINS, MUNG BEANS, PASTURE, PEANUTS, PEAS, SORGHUM, SOYBEANS, SUNFLOWERS, TOMATOES AND WINTER CEREALS:

Spray volumes:

For rates less than 1.5 L/ha: Dilute to any convenient volume no less than 1.5 L/ha.

For rates of 1.5 L/ha and higher: apply undiluted or diluted to give any convenient volume.

Droplet Sizes:

When applying at ULTRA LOW VOLUMES (ie: volumes less than 5 L/ha): use a spray of 80-120 microm VMD.

When applying at LOW VOLUMES (ie: volumes greater than 5 L/ha): use a fine spray (100-150 microm VMD).

To reduce drift and optimise results, avoid application in calm conditions and apply in light to moderate crosswinds.

Fungicide Resistance Warning

For insecticide resistance management, Ospray Methomyl 225 Insecticide is a Group 1A Insecticide. Some naturally occurring insect biotypes resistant to Ospray Methomyl 225 Insecticide and other Group 1A insecticides may exist through normal genetic variability in any insect population. The resistant individuals can eventually dominate the insect population if Ospray Methomyl 225 Insecticide or other Group 1A insecticides are used repeatedly. The effectiveness of Ospray Methomyl 225 Insecticide on resistant individuals could be significantly reduced. Since the occurrence of resistant individuals is diffi cult to detect prior to use, Ospray Pty Ltd accepts no liability for any losses that may result from the failure of Ospray Methomyl 225 Insecticide to control resistant insects. Ospray Methomyl 225 Insecticide may be subject to specific resistance management strategies. For further information, contact your local supplier, Ospray representative or local agriculture department agronomist.

Compatibility

Ospray Methomyl 225 Insecticide is compatible with a wide range of pesticides in common use, eg: HALLMARK+ 10 ULV, Endosan+ 240 ULV, Thiodan+ ULV, Endosulfan ULV and Endosulfan ULV240.

Restraints

DO NOT use in covered or protected situations such as glasshouses, greenhouses or plastic tunnels.

Protection of wildlife, fish, crustaceans and environment

This product is toxic to wildlife. Birds feeding on treated areas may be killed.

Dangerous to fish. DO NOT contaminate fi sh ponds, dams, rivers or streams with this chemical or the used container.

Safety Directions

Very dangerous, particularly the concentrate. Product and spray are poisonous if absorbed by skin contact, or inhaled or swallowed. Attacks eyes. Will irritate the nose, throat and skin. Repeated minor exposure may have a cumulative poisoning effect. Avoid contact with eyes, skin and clothing. DO NOT inhale vapour or spray mist. Protect eyes while using. Obtain an emergency supply of atropine tablets 0.6 mg. When opening the container and preparing the spray, wear elbow-length PVC gloves and face shield. When using the prepared spray, wear:

- cotton overalls buttoned to the neck and wrist;

- washable hat;

- elbow-length PVC gloves;

- impervious footwear; and

- half face-piece respirator with combined dust and gas cartridge (canister).

If clothing becomes contaminated with product or wet with spray, remove clothing immediately. If product or spray on skin, immediately wash area with soap and water. After use and before eating, drinking or smoking, wash hands, arms and face thoroughly with soap and water. After each day's use, wash gloves, face shield, respirator (if rubber, wash with detergent and warm water) and contaminated clothing.

Storage

Store in the closed, original container in a cool, well-ventilated area. DO NOT store for prolonged periods in direct sunlight. DO NOT dispose of undiluted chemicals on-site.

Disposal

The method of disposal of the container depends on the container type. Read the 'Storage and Disposal' instructions on this label that is attached to the container.

Precautions

Caution

Keep unprotected persons out of operational area during treatment and while there is a danger of drift. Avoid contact with spray residues. Keep container closed when not in use.

Re-entry Period

Keep unprotected persons out of treated area for at least 24 hours.

Product details last updated on 25 Jun 2010

DISCLAIMER: This is not the METHOMYL 225 label. To view or print the label for this product, click the "MSDS/Label" tab at the top of this page. Always follow label instructions.

For specialist advice in an EMERGENCY only phone 1800 033 111, TOLL-FREE, ALL-HOURS, NATIONWIDE

APVMA Code :61143 Active Constituent(s): 500g/Latrazine

Registered For Commercial Use Domestic Use Overview Controls weeds and grasses in sorghum, maize, sugarcane, lupins, TT-canola and other crops. Chemical Group triazine General Instructions ATRAZINE 500 is a pre- and post-emergent herbicide which will selectively control: - weeds and grasses in sorghum, maize, sweet corn, sugar cane, lupins, broom millet, saccaline and forage sorghum - mintweed in established lucerne - Brome Grass in sirocco phalaris, demeter fescue and currie cocksfoot grass seed crops - provide control of weeds and grasses growing on a fallow in a conservation tillage system. Established perennial species are not satisfactorily controlled at the rates recommended. Duration and effectiveness of control depends on the amount of chemical applied, soil type, rainfall and particular weed species. DO NOT apply more than 6 litres per hectare per year for all crops except forestry. DO NOT apply more than 9 litres per hectare per year in forestry situations in sandy soils and soils classed as highly erodible and not more than 16 litres per hectare per year for clay loams and heavier textured soils. Integrated Weed Management Strategy For TT-Canola The use of this product in TT-canola is subject to an Integrated Weed Management Strategy for the use of triazine herbicides in TT-canola. The Strategy encompasses: - Integrated Weed Management; - the specifi c management of crop plant volunteers and outcrossing to other plants; and - triazine herbicide residue management (agronomic and environment) Compliance with registered label directions and adoption of the principles outlined in the Strategy will assist with implementation of crop management practices that minimise the development of herbicide resistance in treated weeds; reduce the levels of triazine residues in the environment; and manage volunteer plants and outcrossing. Copies of the Strategy are available from a Ospray representative. It is advised that consultation be undertaken with an appropriate agronomist, consultant or Departmental adviser prior to the use of ATRAZINE 500 on TT-Canola. To minimize herbicide resistance: - Avoid dry sowing in heavily weed-infested paddocks. Wait for a weed germination after the opening rains in weedy paddocks. Use a pre-plant knockdown or cultivation. No weeds should be allowed to survive at this stage. - Adapt the weed control program to the anticipated weed spectrum and pressure: Broadleaf Weeds and Ryegrass: use (simazine 500 g/L) or (atrazine 500 g/L) plus trifl uralin pre-emergence. A follow-up with a Group A herbicide (if ryegrass is susceptible) or atrazine 500 g/L may be necessary. Broadleaf Weeds only: use atrazine 500 g/L post-emergence. - DO NOT use atrazine 500 g/L or simazine 500 g/L if the area to be treated had a triazine herbicide applied to it last season - Watch for escapes, especially in paddocks with a long history of Group C herbicide use. - DO NOT use Group C herbicides in consecutive years. Resistance Weed Reporting Growers should collect plant or seed samples where weeds that are normally susceptible to atrazine and simazine may be resistant, get them tested and seek professional advice. To avoid triazine carry-over: On acid soils (pH less than 6.5) - The maximum rate of atrazine 500 g/L or simazine 500 g/L or a combination of the two products to be applied to the crop during the growing season is 4 L/ha. On alkaline soils (pH greater than 6.5) - The maximum rate of atrazine 500 g/L or simazine 500 g/L or a combination of the two products to be applied to the crop during the growing season is 2 L/ha. Post-emergence use - It is recommended that atrazine 500 g/L only be used, and at rates of 2 L/ha or less, on both acid or alkaline soils. Mixing Settling may occur after storage for some weeks. Stir product or invert container several times before opening. Pour the product into the spray vat through a strainer to remove any dry particles or fl akes, which can occasionally occur under hot storage conditions. Add the full quantity of ATRAZINE 500 to the partly fi lled spray tank while agitating. Fill tank and agitate to ensure thorough mixing. Continue agitation while spraying. Agitate vigorously from the bottom if allowed to stand. Reseal partly used container immediately. DO NOT mix or load this product within 20 m of any well, sink or hole or intermittent perennial, stream or river. Application Ground application: application can be made as an overall or band treatment. Minimum band width should be 30 cm. Apply 50 to 100 litres total spray volume per hectare. Aircraft application: with aircraft application the need for good soil moisture at the time of application and follow up rain or irrigation within 10 days is most critical. Apply 20 to 30 litres total spray volume per hectare. DO NOT use human flaggers when applying by aircraft, unless protected by engineering controls such as enclosed cabs. TT-Canola: DO NOT apply to TT-canola by aircraft. Apply only with a low boom sprayer with a 60 m buffer zone downwind of treated fi elds to natural or impounded lakes or dams, and a 20 m buffer zone for any well, sink hole, intermittent or perennial stream. Apply only to areas where run-off is unlikely to occur or where run-off may be captured by farm earthworks. Timing TIME OF APPLICATION (sorghum, maize, broom millet, saccaline, sweet corn) Pre-plant or pre-emergence applications are preferred where grasses are the major problem. (a) Pre-plant application - followed by post-emergence application. Apply after establishment of the seedbed and up to two weeks prior to sowing. Application should preferably be made to moist soil and rain or irrigation should follow application. Mechanical incorporation may also assist. If using this technique on irrigated crops then a post-emergence spray must be applied as soon as possible after the crop has emerged and has developed 2 to 3 leaves. (b) At sowing application - followed by a post-emergence application. Apply at or immediately after planting and before crop and weeds emerge. Application should preferably be made to moist soil and rain or irrigation should follow application. Mechanical incorporation may also assist. If using this technique on irrigated crops then a post-emergence spray must be applied as soon as possible after the crop has emerged and has developed 2 to 3 leaves. (c) At sowing application. Apply at or immediately after planting and before crop and weeds emerge. Application should preferably be made to moist soil and rain or irrigation should follow application. Mechanical incorporation may also assist. Note: applying the total amount as a pre-emergent application increases the risk of crop damage. (d) Post-emergence application Application must be made to seedling broadleaf weeds and grasses when they are not more than 1 cm high. Normally the crop is then at the 2 to 3 leaf stage. For best results the soil should be moist and rain or irrigation should follow application. Add a non-ionic surfactant (100 %) at a rate of 135 mL per 100 L of spray solution, for all post- emergent applications in sorghum, broom millet and saccaline, and 5.5 L/ha of crop oil for maize and sweet corn. See Warning above. Incorporation: If applied to dry soil harrow to incorporate the product into the soil not more than 4 cm deep. Note: should weeds develop after a pre-plant or pre-emergence application a shallow cultivation may assist. Avoid deep cultivation which may throw untreated soil over the sprayed area, as this may seriously reduce weed control. Compatibility Compatible with glyphosate, atrazine, ametryn, diuron, Primatol† Z, dicamba, diquat/paraquat mixtures, hexazinone. In sugar cane only the addition of sodium 2,4-D will assist in short term suppression of Nutgrass and other sedges. Restraints DO NOT plant crops other than those recommended on this label for at least 6 months following treatments of this product at rates of up to 2.5 litres per hectare and for 18 months following treatments of 2.5 to 6.0 litres per hectare. DO NOT apply to waterlogged soil. DO NOT apply if heavy rains or storms that are likely to cause run-off are forecast within two days of application. DO NOT irrigate to the point of run-off for at least two days after application. DO NOT use as a pre-emergence application in sorghum, broom millet or saccaline during the wet season in the northern irrigation areas of Western Australia. DO NOT use a knapsack sprayer for application in eucalypts and Pinus radiata plantations. DO NOT use or apply this product post-emergence in triazine tolerant (TT) Canola on raised beds or where furrows have been created in soil for the purposes of holding or channeling water. DO NOT apply product to any drainage line. Drainage lines show evidence of the action of periodically fl owing water (for example, gravel, pebble, rock and sand bed, scour hole or nick point) and/or an incised channel at least 30 cm deep. DO NOT handle, mix, apply or conduct testing operations in areas susceptible to run-off where drainage results in rapid entry into waterways, particularly where no specifi c and effective action has been taken to prevent run-off into waterways. These areas may include areas mounded perpendicular to the contour, roads, access tracks, snig tracks, and compacted log dumps. Resistance Warning Ospray ATRAZINE 500 Flowable Herbicide is a member of the triazine group of herbicides and has the inhibitors of photosynthesis at photosystem II mode of action. For weed resistance management, this product is a Group C herbicide. Some naturally occurring weed biotypes resistant to ATRAZINE 500 and other Group C herbicides may exist through normal genetic variability in any weed population. The resistant individuals can eventually dominate the weed population if these herbicides are used repeatedly. These resistant weeds will not be controlled by ATRAZINE 500 or other Group C herbicides. Since the occurrence of resistant weeds is diffi cult to detect prior to use, Ospray Pty. Ltd. accepts no liability for any losses that may result from the failure of ATRAZINE 500 to control the resistant weeds. Advice as to strategies and alternative treatments that can be used should be obtained from your local supplier, consultant, local Department of Agriculture, Primary Industries Department or a Ospray representative. Any incidents of resistance must be reported to Ospray Pty. Ltd. Protection of wildlife, fish, crustaceans and environment DO NOT contaminate streams, rivers or waterways with the chemical or used containers. This product is very highly toxic to algae and aquatic macrophytes. DO NOT apply this product within 60 m of natural or impounded lakes or dams. DO NOT use in channels or drains. DO NOT apply under meteorological conditions or from spraying equipment which could be expected to cause drift of this product or spray mix into adjacent areas, particularly wetlands, water bodies or watercourses. Protection of crop, native and other non-target plants DO NOT apply under weather conditions or from spraying equipment which may cause spray to drift onto nearby susceptible plants/crops, cropping lands or pastures. DO NOT apply or drain or fl ush equipment on or near desirable trees or other plants or on areas where their roots may extend or in locations where the chemical may be washed or moved into contact with their roots. DO NOT plant crops other than those recommended on this label for at least 6 months following treatments at rates up to 2.5 litres per hectare and for 18 months following treatments of 2.5 to 6.0 litres per hectare. DO NOT use in channels or drains. DO NOT spray foliage of desirable plants. DO NOT apply high rates of application to heavier soils if roots of desirable shrubs and trees are near the surface. DO NOT use near newly planted shrubs, young ornamentals or species with shallow roots. DO NOT plant crops other than those recommended on this label for at least 6 months following treatments at rates up to 2.5 litres per hectare and for 18 months following treatments of 2.5 to 6.0 litres per hectare. Safety Directions Avoid contact with skin and eyes. DO NOT inhale spray mist. When preparing spray and using the prepared spray wear elbow-length PVC gloves. After use and before eating, drinking or smoking wash hands, arms and face thoroughly with soap and water. After each days use wash gloves. Storage Store in the closed, original container in a cool, well-ventilated area. DO NOT store for prolonged periods in direct sunlight. Disposal Triple or preferably pressure rinse containers before disposal. Add rinsings to spray tank. DO NOT dispose of undiluted chemicals on-site. If recycling, replace cap and return clean containers to recycler or designated collection point (contact drumMuster Collection agency or Local Council for collection sites). If not recycling, break, crush, or puncture and bury empty containers in a local authority landfi ll. If no landfi ll is available, bury the containers below 500 mm in a disposal pit specifi cally marked and set up for this purpose clear of waterways, desirable vegetation and tree roots. Empty containers and product should not be burnt. For refi llable containers, empty contents fully into application equipment. Close all valves and return to point of supply for refill or storage. Precautions Warning Sorghum, broom millet, saccaline Heavy rain immediately after application may result in excessive concentrations of herbicide in the seed furrow, encouraging crop injury. This is most likely to occur in pre-plant or pre- emergence applications using rates in excess of 3.6 L/ha. To avoid the likelihood of herbicide injury use techniques (a), (b) or (d) in the Time of application section. DO NOT use as a pre-emergence application in the wet season in the northern irrigation areas of Western Australia. When sowing is made on the fl at avoid application to ridged soil. Applying the total amount of product as a pre-emergence application will increase the risk of crop injury in the event of heavy rain after application. Maize, sweet corn For post-emergent application add crop oil at a rate of 5.5 L/ha if grass weeds are a problem. Ensure that the mixture is continually agitated. DO NOT apply mixtures of crop oil to stressed crops, inbred lines or breeding stock as injury may occur. If only broadleaf weeds are a problem, add 135 mL of 100% non-ionic surfactant per 100 L of spray mixture. Summer crops Heavy rains immediately following an application tend to result in excessive concentrations of herbicide in the seed furrow, thus encouraging possible crop injury. This is most likely to occur when a pre-plant or pre-emergence application is made using rates in excess of 3.6 litres per hectare. To avoid the likelihood of herbicide injury follow Time of Application (a), (b) or (d) listed below. Re-entry Period DO NOT enter treated areas without protective clothing until spray has dried. Product details last updated on 25 Jun 2010

DISCLAIMER: This is not the ATRAZINE 500 FLOWABLE HERBICIDE label. To view or print the label for this product, click the "MSDS/Label" tab at the top of this page. Always follow label instructions.

For specialist advice in an EMERGENCY only phone , TOLL-FREE, ALL-HOURS, NATIONWIDE